Skip to main content
O Trucking
Truck Component

International Aftertreatment (A26 engine + legacy)

Navistar (International) · Aftertreatment / Emissions · DPF + SCR + DEF

Class 8 In production
Aftertreatment / Emissions
Manufacturer
Navistar (International)
Category
Aftertreatment / Emissions
Subtype
DPF + SCR + DEF
Class
Class 8

What this component does

International Aftertreatment is Navistar's emissions control system for the International A26 (2016+) and S13 (2024+) engines. Notable history: Navistar's previous-generation engines (MaxxForce 13, 2010-2014) used EGR-only emissions strategy without SCR — which failed catastrophically and resulted in class-action lawsuits. The A26 (2016+) introduced full DPF + SCR + DEF aftertreatment matching industry-standard architecture, restoring International's emissions reliability.

Specifications
Manufacturer
Navistar (International)
Category
Aftertreatment / Emissions
Subtype
DPF + SCR + DEF
Truck class
Class 8
Production
2016–present
Applications
International A26 and S13 engines
Design and engineering

DOC + DPF + SCR + DEF dosing — standard architecture. A26 introduced 2016; S13 (Traton-derived) launched 2024 with updated emissions hardware.

Generations
  • MaxxForce EGR-only (avoid) (2010–2014)
    Navistar's no-SCR strategy. Catastrophic failure history. Class-action settlements.
  • International A26 + SCR (2016–present)
    Industry-standard SCR + DEF architecture.
  • International S13 (Traton-derived) (2024–present)
    Next-generation with EPA 2027 prep.
Reliability and longevity

Post-2016 A26 aftertreatment is comparable to industry. Avoid 2010-2014 MaxxForce 13 trucks — class-action lawsuit history.

Common problems

MaxxForce 13 era (2010-2014): catastrophic EGR cooler failures, oil cooler failures, head gasket failures. A26 (2016+): industry-standard DEF/SCR issues.

Maintenance schedule

Standard DEF/DPF/SCR service intervals (A26 and S13).

Pros and cons

Pros

  • ✓A26 (2016+) restored International emissions reliability
  • ✓S13 (2024+) is Traton/Scania-derived — global proven technology

Cons

  • !MaxxForce 13 (2010-2014) is widely-known disaster
  • !International brand recovery from MaxxForce era ongoing
  • !Smaller dealer network for parts vs Daimler/Volvo
Trucks that use this component
Related DTC codes
Other Aftertreatment / Emissions components

Related

Frequently Asked Questions

What is the International Aftertreatment (A26 engine + legacy) system?
The International Aftertreatment (A26 engine + legacy) is the emissions control system for Class 8 trucks with Navistar (International) engines. International Aftertreatment is Navistar's emissions control system for the International A26 (2016+) and S13 (2024+) engines. Notable history: Navistar's previous-generation engines (MaxxForce 13, 2010-2014) used EGR-only emissions strategy without SCR — which failed catastrophically and resulted
What is DEF and how much do I use?
DEF (Diesel Exhaust Fluid) is a urea-water solution that's injected into the exhaust stream to convert NOx to harmless nitrogen and water vapor via the SCR catalyst. Typical consumption: 1 gallon DEF per 50 gallons of diesel — about 2% of fuel volume. A typical Class 8 long-haul truck uses 5-7 gallons of DEF per 1,000 miles. DEF is available at all truck stops at $2.50-4.00/gallon.
Why does aftertreatment fail so often?
Modern aftertreatment is the #1 source of unscheduled diesel truck downtime. Common failure modes: DEF heater failures (cold weather), NOx sensor degradation at 200-400K miles, DPF face plugging from short trips or extended idle, EGR cooler cracking, SCR catalyst poisoning from sulfur contamination. Major fleets budget $0.05-0.15/mile for aftertreatment-related maintenance over truck life. Tampering (DPF delete) is illegal — federal fines up to $5,000 per violation under the Clean Air Act.
What are common DTC codes for this aftertreatment?
Common codes: P204F, P207F, P2200, P2459, P226C, P244A, P244B. P204F (DEF heater control circuit) and P207F (DEF system performance) are the most-cited. NOx sensors (P2200-P2228) degrade with mileage. DPF efficiency codes (P0420, P0421) typically mean DPF face plugging or DOC failure.
When does the DPF need to be cleaned?
DPF cleaning intervals vary by duty cycle: highway long-haul (high regen rate) typically 350-400K miles. Regional / mixed: 250-350K. Stop-and-go vocational: 150-250K. The truck will display a "DPF cleaning required" warning when soot accumulation exceeds threshold. Cleaning options: ash cleaning ($800-1,500 at a service center) or DPF replacement ($3,000-6,000). Both are required maintenance — driving past the warning eventually triggers a derate that limits the truck to 5 mph.
Can I delete the DPF and DEF system?
**No — this is federally illegal.** Tampering with emissions controls is a violation of the Clean Air Act (42 USC 7522) with federal fines up to $5,000 per violation, plus state penalties. EPA enforcement has increased in 2022-2024 — over 500 fleet inspections nationwide have resulted in fines for DPF-deleted trucks. CARB in California has zero tolerance. Many oil-field operators delete DPF anyway, accepting the risk. Insurance carriers may deny coverage on deleted trucks. **Do not delete emissions equipment for on-road operation.**

Need help diagnosing a component problem?

Ready to Grow Your Trucking Business?

Dispatch support for your trucking business. Explore our current service options.