OBD-II Diagnostic Trouble Code
P2202 — NOx Sensor Circuit Low Bank 1
P2202 indicates the bank 1 NOx sensor circuit is reporting a low signal or low value, typically a failed or shorted measuring element within the sensor. On CAN-based NOx sensors this is usually an internal sensor fault reported by the sensor module.
Severity 4/5
Truck-relevant
Stop within 50 mi
Severity
Stop within 50 mi
NOx Sensor Circuit Low Bank 1
Code
P2202
Category
Powertrain
Subsystem
Aftertreatment
Truck-relevant
Yes
What this means for truckers
Stop within ~50 miles on a Cummins X15, Detroit DD15, PACCAR MX-13. Driving longer risks damaging adjacent components (turbo housing, head gasket, aftertreatment) and turning a $300 fix into a $3,000 fix.
Before you replace parts — try this first
P2202 on the Aftertreatment system is most often failed nox sensor element or module — not a dead part. On commercial diesels especially, work these in order before spending money on parts:
- Confirm the symptoms. Match what your truck is doing to the Symptoms section below. If the code is set but the symptoms are not there, clear the code and re-test after a drive cycle — it may not return.
- Clean and dry the sensor connector. Water, road salt, or oil seeping into a connector is the #1 fake sensor failure. Disconnect, look for green corrosion or moisture, spray with electrical contact cleaner, dry, reseat. Many faults clear here for $0.
- Inspect the wiring harness. Trace the wire from the sensor toward the ECM — look for chafing against the engine block, melted insulation near the turbo or exhaust, or pinch points where a clamp has rubbed through.
- Test the sensor before swapping it. Most Common Causes (below) list the expected voltage or resistance range — a $20 multimeter saves a $300 sensor swap that does not fix the problem.
- Only then, replace the part. Use the OEM or a tier-1 aftermarket. Cheap sensors throw the same code in two weeks.
Symptoms
Emissions or check-engine light, possible changes in DEF dosing and, if left, a progressive inducement derate. Driveability is usually normal at first.
Common causes
- CommonFailed NOx sensor element or module ($450–$1200)
- OccasionalDamaged probe-to-module cable (usually requires replacing the sensor assembly) ($450–$1200)
- OccasionalLow supply voltage to the sensor module ($100–$400)
- RareECM fault ($800–$2500)
How to fix
Verify battery supply and ground at the NOx sensor module
When to use: First check
Inspect the probe cable between sensor and module for heat damage
When to use: When supply is good
Replace the NOx sensor assembly
When to use: When supply and wiring are good
Affects most
No specific vehicle pattern found in our complaint database. This code can appear on any vehicle that supports OBD-II diagnostics.
Related
- → Browse all DTC trouble codes
- → Decode a VIN to check codes for your truck
- → Owner-operator maintenance guides
- → P229E — NOx Sensor Circuit Bank 1 Sensor 2
- → P229F — NOx Sensor Bank 1 Sensor 2
- → P22A4 — Reductant Heater B Control Circuit/Open
- → P22A5 — Reductant Heater B Control Circuit Low
- → P22A6 — Reductant Heater B Control Circuit High
Frequently Asked Questions
Can I drive with code P2202?
Drive with caution. P2202 is severity 4 — stop within ~50 miles. Most commercial diesel codes at this severity (turbo, fuel rail, transmission solenoid) can damage adjacent expensive components if left unrepaired. Get to a service location before highway-speed loads.
How much does it cost to fix P2202 on a commercial truck?
Total repair cost ranges $100–$2500 depending on the root cause. The cheapest fix is usually the first one listed below — Failed NOx sensor element or module — which is also the most common. On commercial trucks the cost is usually higher than passenger vehicles due to part availability and shop labor rates ($120–185/hour at most truck shops, vs $90–130 at general auto shops). DIY-capable fixes (sensors, hoses, filters) are at the low end; major component replacements (turbo actuator, high-pressure fuel pump, transmission solenoid pack) are at the high end. Always diagnose with a scan tool BEFORE replacing parts — guessing wrong on a $1,500 turbo actuator when the actual issue was a $30 boost hose is a common expensive mistake.
Will P2202 fail a DOT inspection?
Yes — P2202 is an emissions-related code, and DOT inspectors check emissions compliance. An active emissions code with a check engine light can result in an out-of-service violation under FMCSA Part 393. The truck typically can't be moved until the code is cleared. Repeated emissions violations escalate to CSA scores.
What's the difference between P2202 and related codes?
P2202 is closely related to: P229E (NOx Sensor Circuit Bank 1 Sensor 2), P229F (NOx Sensor Bank 1 Sensor 2), P22A4 (Reductant Heater B Control Circuit/Open), P22A5 (Reductant Heater B Control Circuit Low). These codes share the same subsystem (aftertreatment) and often appear together. If you see this code, scan for the full code list — fixing the root cause usually clears multiple companion codes at once. If only P2202 is set without the companions, the issue is more isolated.
How do I prevent P2202 from coming back after a repair?
For P2202 (NOx Sensor Circuit Low Bank 1), prevention centers on the aftertreatment system. Run quality DEF (verify supplier — BlueDEF, PEAK, Yara Air1). Don't skip parked regens — when the dash asks for one, do it. Avoid extended idle time which fouls the DPF. Replace NOx sensors at the OEM interval (typically 400K miles).