OBD-II Diagnostic Trouble Code
P2047 — Reductant Injector Circuit/Open Bank 1 Unit 1
P2047 means the ECM found an open circuit in the reductant (DEF) injector, or doser, control circuit for bank 1 unit 1. When the ECM tries to drive the doser solenoid it does not see the expected current, which points to a broken wire, disconnected connector or an open coil inside the doser.
Severity 4/5
Truck-relevant
Stop within 50 mi
Severity
Stop within 50 mi
Reductant Injector Circuit/Open Bank 1 Unit 1
Code
P2047
Category
Powertrain
Subsystem
Aftertreatment
Truck-relevant
Yes
What this means for truckers
P2047 (Reductant Injector Circuit/Open Bank 1 Unit 1) — DEF dosing injector electrical fault. The valve that meters DEF into the SCR catalyst won't fire. Truck will eventually derate. Replacement: $400-900.
Before you replace parts — try this first
P2047 on the Aftertreatment system is most often unplugged, corroded or heat-damaged doser connector — not a dead part. On commercial diesels especially, work these in order before spending money on parts:
- Confirm the symptoms. Match what your truck is doing to the Symptoms section below. If the code is set but the symptoms are not there, clear the code and re-test after a drive cycle — it may not return.
- Clean and dry the sensor connector. Water, road salt, or oil seeping into a connector is the #1 fake sensor failure. Disconnect, look for green corrosion or moisture, spray with electrical contact cleaner, dry, reseat. Many faults clear here for $0.
- Inspect the wiring harness. Trace the wire from the sensor toward the ECM — look for chafing against the engine block, melted insulation near the turbo or exhaust, or pinch points where a clamp has rubbed through.
- Test the sensor before swapping it. Most Common Causes (below) list the expected voltage or resistance range — a $20 multimeter saves a $300 sensor swap that does not fix the problem.
- Only then, replace the part. Use the OEM or a tier-1 aftermarket. Cheap sensors throw the same code in two weeks.
Symptoms
Check-engine and DEF/SCR warning lights, no DEF dosing, sharply higher NOx, and an emissions derate countdown that will end in reduced power and speed if not repaired. DEF level will stop dropping because none is being used.
Common causes
- CommonUnplugged, corroded or heat-damaged doser connector ($80–$300)
- CommonOpen coil in the DEF doser ($400–$1200)
- OccasionalBroken wire in the doser harness near the exhaust ($100–$400)
- RareControl module driver fault ($1000–$3000)
How to fix
Inspect the doser connector for heat damage, crystallized DEF and loose fit
When to use: First step
Measure doser coil resistance and compare to OEM specification
When to use: To confirm whether the doser coil is open
Check continuity of both doser wires back to the control module
When to use: When the doser coil measures good
Replace the doser and run the OEM dosing test
When to use: When the coil is open
Affects most
No specific vehicle pattern found in our complaint database. This code can appear on any vehicle that supports OBD-II diagnostics.
Related
- → Browse all DTC trouble codes
- → Decode a VIN to check codes for your truck
- → Owner-operator maintenance guides
- → P2002 — Diesel Particulate Filter Efficiency Below Threshold (Bank 1)
- → P2003 — Diesel Particulate Filter Efficiency Below Threshold (Bank 2)
- → P2031 — Exhaust Gas Temperature Sensor Bank 1 Sensor 2
- → P2032 — Exhaust Gas Temperature Sensor Bank 1 Sensor 2 Low
- → P2033 — Exhaust Gas Temperature Sensor Bank 1 Sensor 2 High
Frequently Asked Questions
Can I drive with code P2047?
Drive with caution. P2047 is severity 4 — stop within ~50 miles. Most commercial diesel codes at this severity (turbo, fuel rail, transmission solenoid) can damage adjacent expensive components if left unrepaired. Get to a service location before highway-speed loads.
How much does it cost to fix P2047 on a commercial truck?
Total repair cost ranges $80–$3000 depending on the root cause. The cheapest fix is usually the first one listed below — Unplugged, corroded or heat-damaged doser connector — which is also the most common. On commercial trucks the cost is usually higher than passenger vehicles due to part availability and shop labor rates ($120–185/hour at most truck shops, vs $90–130 at general auto shops). DIY-capable fixes (sensors, hoses, filters) are at the low end; major component replacements (turbo actuator, high-pressure fuel pump, transmission solenoid pack) are at the high end. Always diagnose with a scan tool BEFORE replacing parts — guessing wrong on a $1,500 turbo actuator when the actual issue was a $30 boost hose is a common expensive mistake.
Will P2047 fail a DOT inspection?
Yes — P2047 is an emissions-related code, and DOT inspectors check emissions compliance. An active emissions code with a check engine light can result in an out-of-service violation under FMCSA Part 393. The truck typically can't be moved until the code is cleared. Repeated emissions violations escalate to CSA scores.
What's the difference between P2047 and related codes?
P2047 is closely related to: P2002 (Diesel Particulate Filter Efficiency Below Threshold (Bank 1)), P2003 (Diesel Particulate Filter Efficiency Below Threshold (Bank 2)), P2031 (Exhaust Gas Temperature Sensor Bank 1 Sensor 2), P2032 (Exhaust Gas Temperature Sensor Bank 1 Sensor 2 Low). These codes share the same subsystem (aftertreatment) and often appear together. If you see this code, scan for the full code list — fixing the root cause usually clears multiple companion codes at once. If only P2047 is set without the companions, the issue is more isolated.
How do I prevent P2047 from coming back after a repair?
For P2047 (Reductant Injector Circuit/Open Bank 1 Unit 1), prevention centers on the aftertreatment system. Run quality DEF (verify supplier — BlueDEF, PEAK, Yara Air1). Don't skip parked regens — when the dash asks for one, do it. Avoid extended idle time which fouls the DPF. Replace NOx sensors at the OEM interval (typically 400K miles).