OBD-II Diagnostic Trouble Code
P2003 — Diesel Particulate Filter Efficiency Below Threshold (Bank 2)
P2003 means DPF efficiency is below threshold on bank 2. The ECM sees that the bank 2 filter is not trapping soot properly, usually because it is cracked, melted or its pressure monitoring is faulty. It applies only to engines with a second DPF.
Severity 4/5
Truck-relevant
Stop within 50 mi
Severity
Stop within 50 mi
Diesel Particulate Filter Efficiency Below Threshold (Bank 2)
Code
P2003
Category
Powertrain
Subsystem
Aftertreatment
Truck-relevant
Yes
What this means for truckers
Stop within ~50 miles on a Cummins X15, Detroit DD15, PACCAR MX-13. Driving longer risks damaging adjacent components (turbo housing, head gasket, aftertreatment) and turning a $300 fix into a $3,000 fix.
Before you replace parts — try this first
P2003 on the Aftertreatment system is most often cracked or melted bank 2 dpf — not a dead part. On commercial diesels especially, work these in order before spending money on parts:
- Confirm the symptoms. Match what your truck is doing to the Symptoms section below. If the code is set but the symptoms are not there, clear the code and re-test after a drive cycle — it may not return.
- Clean and dry the sensor connector. Water, road salt, or oil seeping into a connector is the #1 fake sensor failure. Disconnect, look for green corrosion or moisture, spray with electrical contact cleaner, dry, reseat. Many faults clear here for $0.
- Inspect the wiring harness. Trace the wire from the sensor toward the ECM — look for chafing against the engine block, melted insulation near the turbo or exhaust, or pinch points where a clamp has rubbed through.
- Test the sensor before swapping it. Most Common Causes (below) list the expected voltage or resistance range — a $20 multimeter saves a $300 sensor swap that does not fix the problem.
- Only then, replace the part. Use the OEM or a tier-1 aftermarket. Cheap sensors throw the same code in two weeks.
Symptoms
Visible soot at the tailpipe, check-engine light, possible derate and low DPF pressure readings.
Common causes
- CommonCracked or melted bank 2 DPF ($2000–$7000)
- CommonFaulty differential pressure sensor ($200–$600)
- OccasionalCracked or disconnected sensor hoses ($80–$300)
- OccasionalExhaust leak around the DPF ($150–$600)
How to fix
Check differential pressure readings and hoses
When to use: First step
Inspect the DPF outlet for soot
When to use: To confirm failure
Replace the sensor or hoses
When to use: When they are bad
Replace the DPF and correct the cause of excess soot or overheating
When to use: When the filter is cracked
Affects most
No specific vehicle pattern found in our complaint database. This code can appear on any vehicle that supports OBD-II diagnostics.
Related
- → Browse all DTC trouble codes
- → Decode a VIN to check codes for your truck
- → Owner-operator maintenance guides
- → P2002 — Diesel Particulate Filter Efficiency Below Threshold (Bank 1)
- → P2031 — Exhaust Gas Temperature Sensor Bank 1 Sensor 2
- → P2032 — Exhaust Gas Temperature Sensor Bank 1 Sensor 2 Low
- → P2033 — Exhaust Gas Temperature Sensor Bank 1 Sensor 2 High
- → P2080 — Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 1 Sensor 1
Frequently Asked Questions
Can I drive with code P2003?
Drive with caution. P2003 is severity 4 — stop within ~50 miles. Most commercial diesel codes at this severity (turbo, fuel rail, transmission solenoid) can damage adjacent expensive components if left unrepaired. Get to a service location before highway-speed loads.
How much does it cost to fix P2003 on a commercial truck?
Total repair cost ranges $80–$7000 depending on the root cause. The cheapest fix is usually the first one listed below — Cracked or melted bank 2 DPF — which is also the most common. On commercial trucks the cost is usually higher than passenger vehicles due to part availability and shop labor rates ($120–185/hour at most truck shops, vs $90–130 at general auto shops). DIY-capable fixes (sensors, hoses, filters) are at the low end; major component replacements (turbo actuator, high-pressure fuel pump, transmission solenoid pack) are at the high end. Always diagnose with a scan tool BEFORE replacing parts — guessing wrong on a $1,500 turbo actuator when the actual issue was a $30 boost hose is a common expensive mistake.
Will P2003 fail a DOT inspection?
Yes — P2003 is an emissions-related code, and DOT inspectors check emissions compliance. An active emissions code with a check engine light can result in an out-of-service violation under FMCSA Part 393. The truck typically can't be moved until the code is cleared. Repeated emissions violations escalate to CSA scores.
What's the difference between P2003 and related codes?
P2003 is closely related to: P2002 (Diesel Particulate Filter Efficiency Below Threshold (Bank 1)), P2031 (Exhaust Gas Temperature Sensor Bank 1 Sensor 2), P2032 (Exhaust Gas Temperature Sensor Bank 1 Sensor 2 Low), P2033 (Exhaust Gas Temperature Sensor Bank 1 Sensor 2 High). These codes share the same subsystem (aftertreatment) and often appear together. If you see this code, scan for the full code list — fixing the root cause usually clears multiple companion codes at once. If only P2003 is set without the companions, the issue is more isolated.
How do I prevent P2003 from coming back after a repair?
For P2003 (Diesel Particulate Filter Efficiency Below Threshold (Bank 2)), prevention centers on the aftertreatment system. Run quality DEF (verify supplier — BlueDEF, PEAK, Yara Air1). Don't skip parked regens — when the dash asks for one, do it. Avoid extended idle time which fouls the DPF. Replace NOx sensors at the OEM interval (typically 400K miles).