OBD-II Diagnostic Trouble Code
P2014 — Intake Manifold Runner Position Sensor/Switch Bank 1
P2014 means the ECM detected a fault in the intake manifold runner position sensor or switch circuit on bank 1, such as no signal or an invalid signal.
Severity 3/5
Truck-relevant
Service this week
Severity
Service this week
Intake Manifold Runner Position Sensor/Switch Bank 1
Code
P2014
Category
Powertrain
Subsystem
Air Flow
Truck-relevant
Yes
What this means for truckers
P2014 (Intake Runner Position Sensor) — IMRC position feedback sensor has a circuit fault.
Before you replace parts — try this first
P2014 on the Air Flow system is most often faulty position sensor — not a dead part. On commercial diesels especially, work these in order before spending money on parts:
- Confirm the symptoms. Match what your truck is doing to the Symptoms section below. If the code is set but the symptoms are not there, clear the code and re-test after a drive cycle — it may not return.
- Clean and dry the sensor connector. Water, road salt, or oil seeping into a connector is the #1 fake sensor failure. Disconnect, look for green corrosion or moisture, spray with electrical contact cleaner, dry, reseat. Many faults clear here for $0.
- Inspect the wiring harness. Trace the wire from the sensor toward the ECM — look for chafing against the engine block, melted insulation near the turbo or exhaust, or pinch points where a clamp has rubbed through.
- Test the sensor before swapping it. Most Common Causes (below) list the expected voltage or resistance range — a $20 multimeter saves a $300 sensor swap that does not fix the problem.
- Only then, replace the part. Use the OEM or a tier-1 aftermarket. Cheap sensors throw the same code in two weeks.
Symptoms
Check-engine light, possible reduced power or rough idle, and runner control that may be disabled.
Common causes
- CommonFaulty position sensor ($100–$400)
- CommonWiring or connector fault ($80–$300)
- Occasional5V reference problem ($100–$400)
- RareECM fault ($800–$2500)
How to fix
Check sensor reference, ground and signal
When to use: First step
Inspect wiring and connector
When to use: When the signal is missing
Replace the sensor or actuator assembly
When to use: When the sensor is faulty
Affects most
No specific vehicle pattern found in our complaint database. This code can appear on any vehicle that supports OBD-II diagnostics.
Related
- → Browse all DTC trouble codes
- → Decode a VIN to check codes for your truck
- → Owner-operator maintenance guides
- → P2002 — Diesel Particulate Filter Efficiency Below Threshold (Bank 1)
- → P2003 — Diesel Particulate Filter Efficiency Below Threshold (Bank 2)
- → P2031 — Exhaust Gas Temperature Sensor Bank 1 Sensor 2
- → P2032 — Exhaust Gas Temperature Sensor Bank 1 Sensor 2 Low
- → P2033 — Exhaust Gas Temperature Sensor Bank 1 Sensor 2 High
Frequently Asked Questions
Can I drive with code P2014?
P2014 is severity 3 — plan service within a few days. Performance is likely degraded already (you may feel reduced power, harsher shifts, or slightly worse fuel economy). Continuing to drive risks additional damage to adjacent components.
How much does it cost to fix P2014 on a commercial truck?
Total repair cost ranges $80–$2500 depending on the root cause. The cheapest fix is usually the first one listed below — Faulty position sensor — which is also the most common. On commercial trucks the cost is usually higher than passenger vehicles due to part availability and shop labor rates ($120–185/hour at most truck shops, vs $90–130 at general auto shops). DIY-capable fixes (sensors, hoses, filters) are at the low end; major component replacements (turbo actuator, high-pressure fuel pump, transmission solenoid pack) are at the high end. Always diagnose with a scan tool BEFORE replacing parts — guessing wrong on a $1,500 turbo actuator when the actual issue was a $30 boost hose is a common expensive mistake.
Will P2014 fail a DOT inspection?
P2014 is generally not a direct DOT inspection fail item by itself. Inspectors focus on safety-critical systems (brakes, steering, tires, lights, hours-of-service). However, the check engine light alone can trigger additional inspection scrutiny. Best practice: fix the code and clear it before a planned inspection.
What's the difference between P2014 and related codes?
P2014 is closely related to: P2002 (Diesel Particulate Filter Efficiency Below Threshold (Bank 1)), P2003 (Diesel Particulate Filter Efficiency Below Threshold (Bank 2)), P2031 (Exhaust Gas Temperature Sensor Bank 1 Sensor 2), P2032 (Exhaust Gas Temperature Sensor Bank 1 Sensor 2 Low). These codes share the same subsystem (air-flow) and often appear together. If you see this code, scan for the full code list — fixing the root cause usually clears multiple companion codes at once. If only P2014 is set without the companions, the issue is more isolated.
How do I prevent P2014 from coming back after a repair?
For P2014 (Intake Manifold Runner Position Sensor/Switch Bank 1), prevention centers on the air flow system. Service air filter on time. Clean MAF sensor at every air filter change. Inspect intake boots/hoses for cracks — vibration kills them eventually.