OBD-II Diagnostic Trouble Code
U2108 — CAN Bus ABS Communication Error
U2108 is a manufacturer-specific code that, in its most common use, means a CAN bus communication error with the ABS controller, meaning expected ABS messages were not received correctly. The exact definition varies by manufacturer, so check the OEM service information.
Severity 3/5
Truck-relevant
Service this week
Severity
Service this week
CAN Bus ABS Communication Error
Code
U2108
Category
Network
Subsystem
Network
Truck-relevant
Yes
What this means for truckers
U2108 (CAN Bus ABS Communication Error) — same from ABS perspective.
Before you replace parts — try this first
U2108 on the Network system is most often abs module power, fuse or ground fault — not a dead part. On commercial diesels especially, work these in order before spending money on parts:
- Confirm the symptoms. Match what your truck is doing to the Symptoms section below. If the code is set but the symptoms are not there, clear the code and re-test after a drive cycle — it may not return.
- Clean and dry the sensor connector. Water, road salt, or oil seeping into a connector is the #1 fake sensor failure. Disconnect, look for green corrosion or moisture, spray with electrical contact cleaner, dry, reseat. Many faults clear here for $0.
- Inspect the wiring harness. Trace the wire from the sensor toward the ECM — look for chafing against the engine block, melted insulation near the turbo or exhaust, or pinch points where a clamp has rubbed through.
- Test the sensor before swapping it. Most Common Causes (below) list the expected voltage or resistance range — a $20 multimeter saves a $300 sensor swap that does not fix the problem.
- Only then, replace the part. Use the OEM or a tier-1 aftermarket. Cheap sensors throw the same code in two weeks.
Symptoms
ABS and traction lights, cruise or engine brake disabled, and possibly the speedometer or shift quality affected.
Common causes
- CommonABS module power, fuse or ground fault ($50–$300)
- CommonCorroded ABS connector or chassis wiring damage ($150–$600)
- OccasionalLow battery voltage ($100–$700)
- RareABS module failure ($600–$2000)
How to fix
Check ABS fuses, power and grounds
When to use: First step
Inspect the ABS connectors and network wiring for corrosion and chafing
When to use: When power is good
Confirm the OEM code definition
When to use: Before replacing parts
Replace and program the ABS module
When to use: After other causes are ruled out
Affects most
No specific vehicle pattern found in our complaint database. This code can appear on any vehicle that supports OBD-II diagnostics.
Related
Frequently Asked Questions
Can I drive with code U2108?
U2108 is severity 3 — plan service within a few days. Performance is likely degraded already (you may feel reduced power, harsher shifts, or slightly worse fuel economy). Continuing to drive risks additional damage to adjacent components.
How much does it cost to fix U2108 on a commercial truck?
Total repair cost ranges $50–$2000 depending on the root cause. The cheapest fix is usually the first one listed below — ABS module power, fuse or ground fault — which is also the most common. On commercial trucks the cost is usually higher than passenger vehicles due to part availability and shop labor rates ($120–185/hour at most truck shops, vs $90–130 at general auto shops). DIY-capable fixes (sensors, hoses, filters) are at the low end; major component replacements (turbo actuator, high-pressure fuel pump, transmission solenoid pack) are at the high end. Always diagnose with a scan tool BEFORE replacing parts — guessing wrong on a $1,500 turbo actuator when the actual issue was a $30 boost hose is a common expensive mistake.
Will U2108 fail a DOT inspection?
U2108 is generally not a direct DOT inspection fail item by itself. Inspectors focus on safety-critical systems (brakes, steering, tires, lights, hours-of-service). However, the check engine light alone can trigger additional inspection scrutiny. Best practice: fix the code and clear it before a planned inspection.
What's the difference between U2108 and related codes?
U2108 is closely related to: U2100 (Initial Configuration Not Complete), U2105 (CAN Bus ECM Communication Error), U2106 (CAN Bus TCM Communication Error). These codes share the same subsystem (network) and often appear together. If you see this code, scan for the full code list — fixing the root cause usually clears multiple companion codes at once. If only U2108 is set without the companions, the issue is more isolated.
How do I prevent U2108 from coming back after a repair?
For U2108 (CAN Bus ABS Communication Error), prevention centers on the network system. Pay attention to ground connections at every PM — bad grounds are 70% of communication codes. Inspect harness routing for chafe points. Don't disconnect modules with the key on.