OBD-II Diagnostic Trouble Code
U0107 — Lost Communication With Throttle Actuator Control Module
U0107 means the ECM lost communication with the throttle actuator control module, used where electronic throttle control is handled by a separate module. Without this link the ECM cannot confirm throttle position commands. This is most often seen on gas medium-duty trucks; meaning can vary by OEM.
Severity 5/5
Truck-relevant
Stop now
Severity
Stop now — do not drive
Lost Communication With Throttle Actuator Control Module
Code
U0107
Category
Network
Subsystem
Network
Truck-relevant
Yes
What this means for truckers
U0107 (Lost Communication With Throttle Actuator Control Module) — TAC module offline. Drive-by-wire goes to limp.
Before you replace parts — try this first
U0107 on the Network system is most often wiring or connector fault between ecm and throttle module — not a dead part. On commercial diesels especially, work these in order before spending money on parts:
- Confirm the symptoms. Match what your truck is doing to the Symptoms section below. If the code is set but the symptoms are not there, clear the code and re-test after a drive cycle — it may not return.
- Clean and dry the sensor connector. Water, road salt, or oil seeping into a connector is the #1 fake sensor failure. Disconnect, look for green corrosion or moisture, spray with electrical contact cleaner, dry, reseat. Many faults clear here for $0.
- Inspect the wiring harness. Trace the wire from the sensor toward the ECM — look for chafing against the engine block, melted insulation near the turbo or exhaust, or pinch points where a clamp has rubbed through.
- Test the sensor before swapping it. Most Common Causes (below) list the expected voltage or resistance range — a $20 multimeter saves a $300 sensor swap that does not fix the problem.
- Only then, replace the part. Use the OEM or a tier-1 aftermarket. Cheap sensors throw the same code in two weeks.
Symptoms
Reduced power mode, limited throttle response or idle only, stalling and a check-engine or reduced power light. The truck may be unsafe to drive at highway speed.
Common causes
- CommonWiring or connector fault between ECM and throttle module ($150–$600)
- CommonPower or ground loss at the throttle module ($50–$300)
- OccasionalFailed throttle actuator control module ($400–$1200)
- OccasionalLow system voltage ($100–$500)
How to fix
Check module power, ground and fuses
When to use: First step
Inspect and repair wiring and connectors
When to use: When the fault is intermittent
Replace the module and perform throttle relearn
When to use: When wiring and power check good
Affects most
No specific vehicle pattern found in our complaint database. This code can appear on any vehicle that supports OBD-II diagnostics.
Related
- → Browse all DTC trouble codes
- → Decode a VIN to check codes for your truck
- → Owner-operator maintenance guides
- → U0100 — Lost Communication With ECM/PCM A
- → U0101 — Lost Communication With TCM
- → U0102 — Lost Communication With Transfer Case Control Module
- → U0103 — Lost Communication With Gear Shift Module
- → U0104 — Lost Communication With Cruise Control Module
Frequently Asked Questions
Can I drive with code U0107?
No — U0107 is severity 5. Stop and tow if you're not near a service location. Continuing to drive can cause catastrophic engine damage. The cost of a tow ($300–800) is small compared to the cost of an engine rebuild ($15,000+).
How much does it cost to fix U0107 on a commercial truck?
Total repair cost ranges $50–$1200 depending on the root cause. The cheapest fix is usually the first one listed below — Wiring or connector fault between ECM and throttle module — which is also the most common. On commercial trucks the cost is usually higher than passenger vehicles due to part availability and shop labor rates ($120–185/hour at most truck shops, vs $90–130 at general auto shops). DIY-capable fixes (sensors, hoses, filters) are at the low end; major component replacements (turbo actuator, high-pressure fuel pump, transmission solenoid pack) are at the high end. Always diagnose with a scan tool BEFORE replacing parts — guessing wrong on a $1,500 turbo actuator when the actual issue was a $30 boost hose is a common expensive mistake.
Will U0107 fail a DOT inspection?
U0107 is generally not a direct DOT inspection fail item by itself. Inspectors focus on safety-critical systems (brakes, steering, tires, lights, hours-of-service). However, the check engine light alone can trigger additional inspection scrutiny. Best practice: fix the code and clear it before a planned inspection.
What's the difference between U0107 and related codes?
U0107 is closely related to: U0100 (Lost Communication With ECM/PCM A), U0101 (Lost Communication With TCM), U0102 (Lost Communication With Transfer Case Control Module), U0103 (Lost Communication With Gear Shift Module). These codes share the same subsystem (network) and often appear together. If you see this code, scan for the full code list — fixing the root cause usually clears multiple companion codes at once. If only U0107 is set without the companions, the issue is more isolated.
How do I prevent U0107 from coming back after a repair?
For U0107 (Lost Communication With Throttle Actuator Control Module), prevention centers on the network system. Pay attention to ground connections at every PM — bad grounds are 70% of communication codes. Inspect harness routing for chafe points. Don't disconnect modules with the key on.