OBD-II Diagnostic Trouble Code
P2127 — Throttle/Pedal Position Sensor/Switch E Circuit Low Input
P2127 indicates the accelerator pedal position sensor E signal is below its minimum expected voltage. That typically means an open signal, a short to ground or a loss of the sensor's reference supply.
Severity 4/5
Truck-relevant
Stop within 50 mi
Severity
Stop within 50 mi
Throttle/Pedal Position Sensor/Switch E Circuit Low Input
Code
P2127
Category
Powertrain
Subsystem
Throttle
Truck-relevant
Yes
What this means for truckers
P2127 (TPS E Low) — 5th TPS shorted to ground.
Before you replace parts — try this first
P2127 on the Throttle system is most often open or grounded signal wire or damaged pedal connector — not a dead part. On commercial diesels especially, work these in order before spending money on parts:
- Confirm the symptoms. Match what your truck is doing to the Symptoms section below. If the code is set but the symptoms are not there, clear the code and re-test after a drive cycle — it may not return.
- Clean and dry the sensor connector. Water, road salt, or oil seeping into a connector is the #1 fake sensor failure. Disconnect, look for green corrosion or moisture, spray with electrical contact cleaner, dry, reseat. Many faults clear here for $0.
- Inspect the wiring harness. Trace the wire from the sensor toward the ECM — look for chafing against the engine block, melted insulation near the turbo or exhaust, or pinch points where a clamp has rubbed through.
- Test the sensor before swapping it. Most Common Causes (below) list the expected voltage or resistance range — a $20 multimeter saves a $300 sensor swap that does not fix the problem.
- Only then, replace the part. Use the OEM or a tier-1 aftermarket. Cheap sensors throw the same code in two weeks.
Symptoms
The truck commonly drops to a derate or idle-only mode with the check-engine light on. Pedal input may be ignored entirely or work only partially.
Common causes
- CommonOpen or grounded signal wire or damaged pedal connector ($80–$350)
- CommonLost or loaded 5V reference to sensor E ($100–$450)
- OccasionalFailed pedal sensor ($180–$550)
- RareECM internal fault ($800–$2500)
How to fix
Measure the 5V reference and ground at the pedal connector
When to use: First check
Isolate other sensors sharing the reference if it is low
When to use: When multiple 5V sensor codes are present
Check signal continuity to the ECM and for a short to ground
When to use: When power and ground are good
Replace the pedal assembly
When to use: When the harness tests good
Affects most
- Chevrolet Silverado 35001 complaint mention this code
Related
- → Browse all DTC trouble codes
- → Decode a VIN to check codes for your truck
- → Owner-operator maintenance guides
- → P2100 — Throttle Actuator Control Motor Circuit/Open
- → P2101 — Throttle Actuator Control Motor Circuit Range/Performance
- → P2120 — Throttle/Pedal Position Sensor/Switch D Circuit
- → P2128 — Throttle/Pedal Position Sensor/Switch E Circuit High Input
- → P2138 — Throttle/Pedal Position Sensor/Switch D/E Voltage Correlation
- → Complaints on Chevrolet Silverado 3500
Frequently Asked Questions
Can I drive with code P2127?
Drive with caution. P2127 is severity 4 — stop within ~50 miles. Most commercial diesel codes at this severity (turbo, fuel rail, transmission solenoid) can damage adjacent expensive components if left unrepaired. Get to a service location before highway-speed loads.
How much does it cost to fix P2127 on a commercial truck?
Total repair cost ranges $80–$2500 depending on the root cause. The cheapest fix is usually the first one listed below — Open or grounded signal wire or damaged pedal connector — which is also the most common. On commercial trucks the cost is usually higher than passenger vehicles due to part availability and shop labor rates ($120–185/hour at most truck shops, vs $90–130 at general auto shops). DIY-capable fixes (sensors, hoses, filters) are at the low end; major component replacements (turbo actuator, high-pressure fuel pump, transmission solenoid pack) are at the high end. Always diagnose with a scan tool BEFORE replacing parts — guessing wrong on a $1,500 turbo actuator when the actual issue was a $30 boost hose is a common expensive mistake.
Will P2127 fail a DOT inspection?
P2127 is generally not a direct DOT inspection fail item by itself. Inspectors focus on safety-critical systems (brakes, steering, tires, lights, hours-of-service). However, the check engine light alone can trigger additional inspection scrutiny. Best practice: fix the code and clear it before a planned inspection.
What's the difference between P2127 and related codes?
P2127 is closely related to: P2100 (Throttle Actuator Control Motor Circuit/Open), P2101 (Throttle Actuator Control Motor Circuit Range/Performance), P2120 (Throttle/Pedal Position Sensor/Switch D Circuit), P2128 (Throttle/Pedal Position Sensor/Switch E Circuit High Input). These codes share the same subsystem (throttle) and often appear together. If you see this code, scan for the full code list — fixing the root cause usually clears multiple companion codes at once. If only P2127 is set without the companions, the issue is more isolated.
How do I prevent P2127 from coming back after a repair?
For P2127 (Throttle/Pedal Position Sensor/Switch E Circuit Low Input), prevention centers on the throttle system. Clean throttle body at 100K mile intervals. Don't let carbon build up. Avoid extended idle time.