OBD-II Diagnostic Trouble Code
P1162 — Throttle Switch Voltage Low
P1162 is a manufacturer-specific code; the meaning used here is throttle switch signal voltage low. The ECM saw a low signal from the throttle (idle validation) switch circuit. Exact meaning varies by OEM.
Severity 3/5
Truck-relevant
Service this week
Severity
Service this week
Throttle Switch Voltage Low
Code
P1162
Category
Powertrain
Subsystem
Throttle
Truck-relevant
Yes
What this means for truckers
P1162 (Throttle Switch Voltage Low) — drive-by-wire pedal sensor reading low. Same fix family as P0220 series.
Before you replace parts — try this first
P1162 on the Throttle system is most often wiring short to ground — not a dead part. On commercial diesels especially, work these in order before spending money on parts:
- Confirm the symptoms. Match what your truck is doing to the Symptoms section below. If the code is set but the symptoms are not there, clear the code and re-test after a drive cycle — it may not return.
- Clean and dry the sensor connector. Water, road salt, or oil seeping into a connector is the #1 fake sensor failure. Disconnect, look for green corrosion or moisture, spray with electrical contact cleaner, dry, reseat. Many faults clear here for $0.
- Inspect the wiring harness. Trace the wire from the sensor toward the ECM — look for chafing against the engine block, melted insulation near the turbo or exhaust, or pinch points where a clamp has rubbed through.
- Test the sensor before swapping it. Most Common Causes (below) list the expected voltage or resistance range — a $20 multimeter saves a $300 sensor swap that does not fix the problem.
- Only then, replace the part. Use the OEM or a tier-1 aftermarket. Cheap sensors throw the same code in two weeks.
Symptoms
Erratic idle, poor throttle response or reduced power. Check-engine light.
Common causes
- CommonWiring short to ground ($120–$450)
- CommonFailed throttle switch or pedal assembly ($200–$600)
- OccasionalCorroded connector ($100–$300)
- RareECM fault ($900–$2500)
How to fix
Check OEM definition
When to use: First step
Inspect wiring and connector
When to use: Before replacing parts
Test switch voltage while operating the pedal
When to use: To confirm the fault
Replace switch or pedal
When to use: If it fails testing
Affects most
No specific vehicle pattern found in our complaint database. This code can appear on any vehicle that supports OBD-II diagnostics.
Related
- → Browse all DTC trouble codes
- → Decode a VIN to check codes for your truck
- → Owner-operator maintenance guides
- → P1101 — Mass Airflow Sensor Out of Self Test Range
- → P1102 — Mass Airflow Sensor In Range But Lower Than Expected
- → P1103 — Mass Airflow Sensor In Range But Higher Than Expected
- → P110A — Mass Air Flow Sensor Performance
- → P111A — MAF Sensor B Performance
Frequently Asked Questions
Can I drive with code P1162?
P1162 is severity 3 — plan service within a few days. Performance is likely degraded already (you may feel reduced power, harsher shifts, or slightly worse fuel economy). Continuing to drive risks additional damage to adjacent components.
How much does it cost to fix P1162 on a commercial truck?
Total repair cost ranges $100–$2500 depending on the root cause. The cheapest fix is usually the first one listed below — Wiring short to ground — which is also the most common. On commercial trucks the cost is usually higher than passenger vehicles due to part availability and shop labor rates ($120–185/hour at most truck shops, vs $90–130 at general auto shops). DIY-capable fixes (sensors, hoses, filters) are at the low end; major component replacements (turbo actuator, high-pressure fuel pump, transmission solenoid pack) are at the high end. Always diagnose with a scan tool BEFORE replacing parts — guessing wrong on a $1,500 turbo actuator when the actual issue was a $30 boost hose is a common expensive mistake.
Will P1162 fail a DOT inspection?
P1162 is generally not a direct DOT inspection fail item by itself. Inspectors focus on safety-critical systems (brakes, steering, tires, lights, hours-of-service). However, the check engine light alone can trigger additional inspection scrutiny. Best practice: fix the code and clear it before a planned inspection.
What's the difference between P1162 and related codes?
P1162 is closely related to: P1101 (Mass Airflow Sensor Out of Self Test Range), P1102 (Mass Airflow Sensor In Range But Lower Than Expected), P1103 (Mass Airflow Sensor In Range But Higher Than Expected), P110A (Mass Air Flow Sensor Performance). These codes share the same subsystem (throttle) and often appear together. If you see this code, scan for the full code list — fixing the root cause usually clears multiple companion codes at once. If only P1162 is set without the companions, the issue is more isolated.
How do I prevent P1162 from coming back after a repair?
For P1162 (Throttle Switch Voltage Low), prevention centers on the throttle system. Clean throttle body at 100K mile intervals. Don't let carbon build up. Avoid extended idle time.