OBD-II Diagnostic Trouble Code
P1058 — NOx Sensor Heater Circuit Bank 1
P1058 is a manufacturer-specific code; most commonly it means a NOx sensor heater circuit fault for bank 1. The heater brings the sensor element to operating temperature; the ECM or sensor module detected a heater circuit problem. Exact meaning varies by OEM.
Severity 4/5
Truck-relevant
Stop within 50 mi
Severity
Stop within 50 mi
NOx Sensor Heater Circuit Bank 1
Code
P1058
Category
Powertrain
Subsystem
Aftertreatment
Truck-relevant
Yes
What this means for truckers
Stop within ~50 miles on a Cummins X15, Detroit DD15, PACCAR MX-13. Driving longer risks damaging adjacent components (turbo housing, head gasket, aftertreatment) and turning a $300 fix into a $3,000 fix.
Before you replace parts — try this first
P1058 on the Aftertreatment system is most often failed nox sensor heater (sensor and module are replaced as an assembly) — not a dead part. On commercial diesels especially, work these in order before spending money on parts:
- Confirm the symptoms. Match what your truck is doing to the Symptoms section below. If the code is set but the symptoms are not there, clear the code and re-test after a drive cycle — it may not return.
- Clean and dry the sensor connector. Water, road salt, or oil seeping into a connector is the #1 fake sensor failure. Disconnect, look for green corrosion or moisture, spray with electrical contact cleaner, dry, reseat. Many faults clear here for $0.
- Inspect the wiring harness. Trace the wire from the sensor toward the ECM — look for chafing against the engine block, melted insulation near the turbo or exhaust, or pinch points where a clamp has rubbed through.
- Test the sensor before swapping it. Most Common Causes (below) list the expected voltage or resistance range — a $20 multimeter saves a $300 sensor swap that does not fix the problem.
- Only then, replace the part. Use the OEM or a tier-1 aftermarket. Cheap sensors throw the same code in two weeks.
Symptoms
Check-engine light, possible emissions derate and SCR performance monitoring issues. The truck may run normally otherwise.
Common causes
- CommonFailed NOx sensor heater (sensor and module are replaced as an assembly) ($500–$1200)
- CommonWiring or connector fault ($150–$500)
- OccasionalBlown fuse or power supply issue ($50–$250)
- RareECM fault ($900–$2500)
How to fix
Check OEM definition
When to use: First step
Check fuses and power supply to the sensor
When to use: Before testing the sensor
Inspect wiring and connector
When to use: If power is good
Replace the NOx sensor
When to use: When the heater fails testing
Affects most
No specific vehicle pattern found in our complaint database. This code can appear on any vehicle that supports OBD-II diagnostics.
Related
- → Browse all DTC trouble codes
- → Decode a VIN to check codes for your truck
- → Owner-operator maintenance guides
- → P1037 — NOx Sensor Bank 1 Sensor 1
- → P1093 — Fuel Rail Pressure Low During Power Enrichment
- → P1094 — Fuel Rail Pressure Sensor Performance
- → P10DE — Diesel Particulate Filter Soot Level Too High
- → P10DF — Diesel Particulate Filter Soot Level Too High - Service Required
Frequently Asked Questions
Can I drive with code P1058?
Drive with caution. P1058 is severity 4 — stop within ~50 miles. Most commercial diesel codes at this severity (turbo, fuel rail, transmission solenoid) can damage adjacent expensive components if left unrepaired. Get to a service location before highway-speed loads.
How much does it cost to fix P1058 on a commercial truck?
Total repair cost ranges $50–$2500 depending on the root cause. The cheapest fix is usually the first one listed below — Failed NOx sensor heater (sensor and module are replaced as an assembly) — which is also the most common. On commercial trucks the cost is usually higher than passenger vehicles due to part availability and shop labor rates ($120–185/hour at most truck shops, vs $90–130 at general auto shops). DIY-capable fixes (sensors, hoses, filters) are at the low end; major component replacements (turbo actuator, high-pressure fuel pump, transmission solenoid pack) are at the high end. Always diagnose with a scan tool BEFORE replacing parts — guessing wrong on a $1,500 turbo actuator when the actual issue was a $30 boost hose is a common expensive mistake.
Will P1058 fail a DOT inspection?
Yes — P1058 is an emissions-related code, and DOT inspectors check emissions compliance. An active emissions code with a check engine light can result in an out-of-service violation under FMCSA Part 393. The truck typically can't be moved until the code is cleared. Repeated emissions violations escalate to CSA scores.
What's the difference between P1058 and related codes?
P1058 is closely related to: P1037 (NOx Sensor Bank 1 Sensor 1), P1093 (Fuel Rail Pressure Low During Power Enrichment), P1094 (Fuel Rail Pressure Sensor Performance), P10DE (Diesel Particulate Filter Soot Level Too High). These codes share the same subsystem (aftertreatment) and often appear together. If you see this code, scan for the full code list — fixing the root cause usually clears multiple companion codes at once. If only P1058 is set without the companions, the issue is more isolated.
How do I prevent P1058 from coming back after a repair?
For P1058 (NOx Sensor Heater Circuit Bank 1), prevention centers on the aftertreatment system. Run quality DEF (verify supplier — BlueDEF, PEAK, Yara Air1). Don't skip parked regens — when the dash asks for one, do it. Avoid extended idle time which fouls the DPF. Replace NOx sensors at the OEM interval (typically 400K miles).