OBD-II Diagnostic Trouble Code
P0760 — Shift Solenoid C Malfunction
P0760 is a general malfunction of shift solenoid C. The TCM detected that the solenoid C circuit or its hydraulic result is not what it commanded. Depending on the transmission, this code may cover electrical or performance faults, and some OEMs use the more specific codes P0761-P0764 instead.
Severity 4/5
Truck-relevant
Stop within 50 mi
Severity
Stop within 50 mi
Shift Solenoid C Malfunction
Code
P0760
Category
Powertrain
Subsystem
Transmission
Truck-relevant
Yes
What this means for truckers
Stop within ~50 miles on a Cummins X15, Detroit DD15, PACCAR MX-13. Driving longer risks damaging adjacent components (turbo housing, head gasket, aftertreatment) and turning a $300 fix into a $3,000 fix.
Before you replace parts — try this first
P0760 on the Transmission system is most often wiring or connector fault in the solenoid c circuit — not a dead part. On commercial diesels especially, work these in order before spending money on parts:
- Confirm the symptoms. Match what your truck is doing to the Symptoms section below. If the code is set but the symptoms are not there, clear the code and re-test after a drive cycle — it may not return.
- Clean and dry the sensor connector. Water, road salt, or oil seeping into a connector is the #1 fake sensor failure. Disconnect, look for green corrosion or moisture, spray with electrical contact cleaner, dry, reseat. Many faults clear here for $0.
- Inspect the wiring harness. Trace the wire from the sensor toward the ECM — look for chafing against the engine block, melted insulation near the turbo or exhaust, or pinch points where a clamp has rubbed through.
- Test the sensor before swapping it. Most Common Causes (below) list the expected voltage or resistance range — a $20 multimeter saves a $300 sensor swap that does not fix the problem.
- Only then, replace the part. Use the OEM or a tier-1 aftermarket. Cheap sensors throw the same code in two weeks.
Symptoms
Expect missing or erratic gears, harsh or delayed shifts and possible limp-home operation in a fixed gear. A loaded truck may struggle on grades because it cannot select the right ratio. A check-engine or transmission warning light is usually on.
Common causes
- CommonWiring or connector fault in the solenoid C circuit ($120–$500)
- CommonFailed shift solenoid C ($350–$1000)
- OccasionalLow, dirty or overheated transmission fluid ($200–$600)
- OccasionalValve body wear or sticking shift valve ($900–$2800)
- RareTCM fault ($900–$2500)
How to fix
Check fluid level and condition and read freeze-frame data for temperature and gear at the time of the fault
When to use: First step to understand when the fault set
Measure solenoid C resistance and inspect harness and connectors
When to use: To determine if the fault is electrical
Command solenoid C with a scan tool and watch gear ratio response
When to use: When the circuit tests good but shifts are wrong
Replace solenoid C or service the valve body as indicated
When to use: After the faulty part is confirmed
Affects most
No specific vehicle pattern found in our complaint database. This code can appear on any vehicle that supports OBD-II diagnostics.
Related
- → Browse all DTC trouble codes
- → Decode a VIN to check codes for your truck
- → Owner-operator maintenance guides
- → P0700 — Transmission Control System Malfunction
- → P0701 — Transmission Control System Range/Performance
- → P0702 — Transmission Control System Electrical
- → P0703 — Brake Switch B Circuit
- → P0705 — Transmission Range Sensor Circuit Malfunction
Frequently Asked Questions
Can I drive with code P0760?
Drive with caution. P0760 is severity 4 — stop within ~50 miles. Most commercial diesel codes at this severity (turbo, fuel rail, transmission solenoid) can damage adjacent expensive components if left unrepaired. Get to a service location before highway-speed loads.
How much does it cost to fix P0760 on a commercial truck?
Total repair cost ranges $120–$2800 depending on the root cause. The cheapest fix is usually the first one listed below — Wiring or connector fault in the solenoid C circuit — which is also the most common. On commercial trucks the cost is usually higher than passenger vehicles due to part availability and shop labor rates ($120–185/hour at most truck shops, vs $90–130 at general auto shops). DIY-capable fixes (sensors, hoses, filters) are at the low end; major component replacements (turbo actuator, high-pressure fuel pump, transmission solenoid pack) are at the high end. Always diagnose with a scan tool BEFORE replacing parts — guessing wrong on a $1,500 turbo actuator when the actual issue was a $30 boost hose is a common expensive mistake.
Will P0760 fail a DOT inspection?
P0760 typically doesn't fail an inspection on its own. Inspectors focus on safety items (brakes, steering, tires, lights, HOS). Transmission codes only become an issue if the truck has shifting problems severe enough to qualify as 'mechanical fitness' OOS. Fix to prevent escalation.
What's the difference between P0760 and related codes?
P0760 is closely related to: P0700 (Transmission Control System Malfunction), P0701 (Transmission Control System Range/Performance), P0702 (Transmission Control System Electrical), P0703 (Brake Switch B Circuit). These codes share the same subsystem (transmission) and often appear together. If you see this code, scan for the full code list — fixing the root cause usually clears multiple companion codes at once. If only P0760 is set without the companions, the issue is more isolated.
How do I prevent P0760 from coming back after a repair?
For P0760 (Shift Solenoid C Malfunction), prevention centers on the transmission system. Service transmission fluid at the OEM interval (typically 150K–250K miles for HD autos). Don't skip the magnet/strainer inspection. After repair, perform an adaptive shift relearn with a scan tool (or drive 40+ miles for adaptive ECMs to relearn naturally).