OBD-II Diagnostic Trouble Code
P0744 — Torque Converter Clutch Circuit Intermittent
P0744 means the TCM saw the torque converter clutch circuit or operation drop out intermittently, typically from a loose connection or failing solenoid.
Severity 3/5
Truck-relevant
Service this week
Severity
Service this week
Torque Converter Clutch Circuit Intermittent
Code
P0744
Category
Powertrain
Subsystem
Transmission
Truck-relevant
Yes
What this means for truckers
P0744 (TCC Circuit Intermittent) — Torque Converter Clutch engaging/disengaging unexpectedly. Causes harsh feel at highway speed. Fix: replace TCC solenoid or address transmission fluid quality.
Before you replace parts — try this first
P0744 on the Transmission system is most often loose or corroded connector — not a dead part. On commercial diesels especially, work these in order before spending money on parts:
- Confirm the symptoms. Match what your truck is doing to the Symptoms section below. If the code is set but the symptoms are not there, clear the code and re-test after a drive cycle — it may not return.
- Clean and dry the sensor connector. Water, road salt, or oil seeping into a connector is the #1 fake sensor failure. Disconnect, look for green corrosion or moisture, spray with electrical contact cleaner, dry, reseat. Many faults clear here for $0.
- Inspect the wiring harness. Trace the wire from the sensor toward the ECM — look for chafing against the engine block, melted insulation near the turbo or exhaust, or pinch points where a clamp has rubbed through.
- Test the sensor before swapping it. Most Common Causes (below) list the expected voltage or resistance range — a $20 multimeter saves a $300 sensor swap that does not fix the problem.
- Only then, replace the part. Use the OEM or a tier-1 aftermarket. Cheap sensors throw the same code in two weeks.
Symptoms
Converter lockup cycling on and off, RPM fluctuation at cruise, shudder, and an intermittent check-engine light.
Common causes
- CommonLoose or corroded connector ($80–$300)
- CommonIntermittent TCC solenoid ($250–$800)
- OccasionalChafed harness ($120–$450)
How to fix
Wiggle test harness while monitoring TCC status
When to use: First
Repair connector or harness
When to use: When dropouts are reproduced
Replace TCC solenoid
When to use: When the harness is good
Affects most
No specific vehicle pattern found in our complaint database. This code can appear on any vehicle that supports OBD-II diagnostics.
Related
- → Browse all DTC trouble codes
- → Decode a VIN to check codes for your truck
- → Owner-operator maintenance guides
- → P0700 — Transmission Control System Malfunction
- → P0701 — Transmission Control System Range/Performance
- → P0702 — Transmission Control System Electrical
- → P0703 — Brake Switch B Circuit
- → P0705 — Transmission Range Sensor Circuit Malfunction
Frequently Asked Questions
Can I drive with code P0744?
P0744 is severity 3 — plan service within a few days. Performance is likely degraded already (you may feel reduced power, harsher shifts, or slightly worse fuel economy). Continuing to drive risks additional damage to adjacent components.
How much does it cost to fix P0744 on a commercial truck?
Total repair cost ranges $80–$800 depending on the root cause. The cheapest fix is usually the first one listed below — Loose or corroded connector — which is also the most common. On commercial trucks the cost is usually higher than passenger vehicles due to part availability and shop labor rates ($120–185/hour at most truck shops, vs $90–130 at general auto shops). DIY-capable fixes (sensors, hoses, filters) are at the low end; major component replacements (turbo actuator, high-pressure fuel pump, transmission solenoid pack) are at the high end. Always diagnose with a scan tool BEFORE replacing parts — guessing wrong on a $1,500 turbo actuator when the actual issue was a $30 boost hose is a common expensive mistake.
Will P0744 fail a DOT inspection?
P0744 typically doesn't fail an inspection on its own. Inspectors focus on safety items (brakes, steering, tires, lights, HOS). Transmission codes only become an issue if the truck has shifting problems severe enough to qualify as 'mechanical fitness' OOS. Fix to prevent escalation.
What's the difference between P0744 and related codes?
P0744 is closely related to: P0700 (Transmission Control System Malfunction), P0701 (Transmission Control System Range/Performance), P0702 (Transmission Control System Electrical), P0703 (Brake Switch B Circuit). These codes share the same subsystem (transmission) and often appear together. If you see this code, scan for the full code list — fixing the root cause usually clears multiple companion codes at once. If only P0744 is set without the companions, the issue is more isolated.
How do I prevent P0744 from coming back after a repair?
For P0744 (Torque Converter Clutch Circuit Intermittent), prevention centers on the transmission system. Service transmission fluid at the OEM interval (typically 150K–250K miles for HD autos). Don't skip the magnet/strainer inspection. After repair, perform an adaptive shift relearn with a scan tool (or drive 40+ miles for adaptive ECMs to relearn naturally).