OBD-II Diagnostic Trouble Code
P0708 — Transmission Range Sensor Circuit High Input
P0708 indicates the transmission range sensor circuit is reading a high input, typically from an open circuit or a short to voltage. The TCM sees a signal stuck high that doesn't match any valid selector position.
Severity 4/5
Truck-relevant
Stop within 50 mi
Severity
Stop within 50 mi
Transmission Range Sensor Circuit High Input
Code
P0708
Category
Powertrain
Subsystem
Transmission
Truck-relevant
Yes
What this means for truckers
P0708 (Transmission Range Sensor Circuit High Input) — TRS (often called PRNDL switch) reading too high. Typically a wiring short to power. On older Allisons, the TRS gets contaminated and reads erratically.
Before you replace parts — try this first
P0708 on the Transmission system is most often open circuit or disconnected range sensor connector — not a dead part. On commercial diesels especially, work these in order before spending money on parts:
- Confirm the symptoms. Match what your truck is doing to the Symptoms section below. If the code is set but the symptoms are not there, clear the code and re-test after a drive cycle — it may not return.
- Clean and dry the sensor connector. Water, road salt, or oil seeping into a connector is the #1 fake sensor failure. Disconnect, look for green corrosion or moisture, spray with electrical contact cleaner, dry, reseat. Many faults clear here for $0.
- Inspect the wiring harness. Trace the wire from the sensor toward the ECM — look for chafing against the engine block, melted insulation near the turbo or exhaust, or pinch points where a clamp has rubbed through.
- Test the sensor before swapping it. Most Common Causes (below) list the expected voltage or resistance range — a $20 multimeter saves a $300 sensor swap that does not fix the problem.
- Only then, replace the part. Use the OEM or a tier-1 aftermarket. Cheap sensors throw the same code in two weeks.
Symptoms
No-start, wrong or blank gear display, transmission stuck in a default gear, backup lights inoperative, and the check-engine light.
Common causes
- CommonOpen circuit or disconnected range sensor connector ($80–$350)
- CommonFailed range sensor with open internal contacts ($150–$500)
- OccasionalSignal wire shorted to voltage ($120–$450)
- RareTCM fault ($800–$2500)
How to fix
Inspect sensor connector and harness for damage or disconnection
When to use: First
Check sensor outputs and continuity through each position
When to use: When connector is good
Test circuit for short to voltage with sensor and TCM disconnected
When to use: When high voltage is present on a signal line
Replace the range sensor
When to use: When the sensor fails continuity tests
Affects most
No specific vehicle pattern found in our complaint database. This code can appear on any vehicle that supports OBD-II diagnostics.
Related
- → Browse all DTC trouble codes
- → Decode a VIN to check codes for your truck
- → Owner-operator maintenance guides
- → P0700 — Transmission Control System Malfunction
- → P0701 — Transmission Control System Range/Performance
- → P0702 — Transmission Control System Electrical
- → P0703 — Brake Switch B Circuit
- → P0705 — Transmission Range Sensor Circuit Malfunction
Frequently Asked Questions
Can I drive with code P0708?
Drive with caution. P0708 is severity 4 — stop within ~50 miles. Most commercial diesel codes at this severity (turbo, fuel rail, transmission solenoid) can damage adjacent expensive components if left unrepaired. Get to a service location before highway-speed loads.
How much does it cost to fix P0708 on a commercial truck?
Total repair cost ranges $80–$2500 depending on the root cause. The cheapest fix is usually the first one listed below — Open circuit or disconnected range sensor connector — which is also the most common. On commercial trucks the cost is usually higher than passenger vehicles due to part availability and shop labor rates ($120–185/hour at most truck shops, vs $90–130 at general auto shops). DIY-capable fixes (sensors, hoses, filters) are at the low end; major component replacements (turbo actuator, high-pressure fuel pump, transmission solenoid pack) are at the high end. Always diagnose with a scan tool BEFORE replacing parts — guessing wrong on a $1,500 turbo actuator when the actual issue was a $30 boost hose is a common expensive mistake.
Will P0708 fail a DOT inspection?
P0708 typically doesn't fail an inspection on its own. Inspectors focus on safety items (brakes, steering, tires, lights, HOS). Transmission codes only become an issue if the truck has shifting problems severe enough to qualify as 'mechanical fitness' OOS. Fix to prevent escalation.
What's the difference between P0708 and related codes?
P0708 is closely related to: P0700 (Transmission Control System Malfunction), P0701 (Transmission Control System Range/Performance), P0702 (Transmission Control System Electrical), P0703 (Brake Switch B Circuit). These codes share the same subsystem (transmission) and often appear together. If you see this code, scan for the full code list — fixing the root cause usually clears multiple companion codes at once. If only P0708 is set without the companions, the issue is more isolated.
How do I prevent P0708 from coming back after a repair?
For P0708 (Transmission Range Sensor Circuit High Input), prevention centers on the transmission system. Service transmission fluid at the OEM interval (typically 150K–250K miles for HD autos). Don't skip the magnet/strainer inspection. After repair, perform an adaptive shift relearn with a scan tool (or drive 40+ miles for adaptive ECMs to relearn naturally).