OBD-II Diagnostic Trouble Code
P0411 — Secondary Air Injection System Incorrect Flow
P0411 means the secondary air injection system is running, but the ECM did not see the expected effect, usually measured as a lean shift on the upstream oxygen sensors when air is injected. Flow is too low, too high or going to the wrong place.
Severity 2/5
Less common on commercial trucks
Service soon
Severity
Service soon
Secondary Air Injection System Incorrect Flow
Code
P0411
Category
Powertrain
Subsystem
Emissions
Truck-relevant
Less common
What this means for truckers
P0411 (Secondary Air Injection Incorrect Flow) — gas engine code. Air pump runs but volume is wrong.
Before you replace parts — try this first
P0411 on the Emissions system is most often weak or failing air pump — not a dead part. On commercial diesels especially, work these in order before spending money on parts:
- Confirm the symptoms. Match what your truck is doing to the Symptoms section below. If the code is set but the symptoms are not there, clear the code and re-test after a drive cycle — it may not return.
- Clean and dry the sensor connector. Water, road salt, or oil seeping into a connector is the #1 fake sensor failure. Disconnect, look for green corrosion or moisture, spray with electrical contact cleaner, dry, reseat. Many faults clear here for $0.
- Inspect the wiring harness. Trace the wire from the sensor toward the ECM — look for chafing against the engine block, melted insulation near the turbo or exhaust, or pinch points where a clamp has rubbed through.
- Test the sensor before swapping it. Most Common Causes (below) list the expected voltage or resistance range — a $20 multimeter saves a $300 sensor swap that does not fix the problem.
- Only then, replace the part. Use the OEM or a tier-1 aftermarket. Cheap sensors throw the same code in two weeks.
Symptoms
Check-engine light, possibly noise from the pump. The truck normally drives fine, but it may fail emissions testing.
Common causes
- CommonWeak or failing air pump ($300–$1000)
- CommonStuck closed check valve or switching valve ($150–$600)
- OccasionalLeaking or disconnected air hoses ($50–$300)
- OccasionalClogged air passages in the heads or exhaust manifolds ($400–$1500)
- RareSlow upstream oxygen sensors not showing the lean shift ($150–$450)
How to fix
Command the pump on at cold start and watch the upstream oxygen sensors for a lean shift
When to use: First step
Check pump output and hoses for leaks or blockage
When to use: When the oxygen sensors show little change
Test and replace the check valves or switching valve
When to use: When the pump runs but air does not reach the exhaust
Clean carbon from the air passages
When to use: When valves and pump are good but flow is still blocked
Affects most
No specific vehicle pattern found in our complaint database. This code can appear on any vehicle that supports OBD-II diagnostics.
Related
- → Browse all DTC trouble codes
- → Decode a VIN to check codes for your truck
- → Owner-operator maintenance guides
- → P0400 — Exhaust Gas Recirculation Flow Malfunction
- → P0401 — Exhaust Gas Recirculation Flow Insufficient Detected
- → P0402 — Exhaust Gas Recirculation Flow Excessive Detected
- → P0420 — Catalyst System Efficiency Below Threshold (Bank 1)
- → P0421 — Warm Up Catalyst Efficiency Below Threshold (Bank 1)
Frequently Asked Questions
Can I drive with code P0411?
P0411 is severity 2 — service this week. Not an immediate stop, but ignoring it usually compounds the problem. Most common cause for this code is a worn sensor or minor performance fault that won't strand you today but will get more expensive the longer you wait.
How much does it cost to fix P0411 on a commercial truck?
Total repair cost ranges $50–$1500 depending on the root cause. The cheapest fix is usually the first one listed below — Weak or failing air pump — which is also the most common. On commercial trucks the cost is usually higher than passenger vehicles due to part availability and shop labor rates ($120–185/hour at most truck shops, vs $90–130 at general auto shops). DIY-capable fixes (sensors, hoses, filters) are at the low end; major component replacements (turbo actuator, high-pressure fuel pump, transmission solenoid pack) are at the high end. Always diagnose with a scan tool BEFORE replacing parts — guessing wrong on a $1,500 turbo actuator when the actual issue was a $30 boost hose is a common expensive mistake.
Will P0411 fail a DOT inspection?
Yes — P0411 is an emissions-related code, and DOT inspectors check emissions compliance. An active emissions code with a check engine light can result in an out-of-service violation under FMCSA Part 393. The truck typically can't be moved until the code is cleared. Repeated emissions violations escalate to CSA scores.
What's the difference between P0411 and related codes?
P0411 is closely related to: P0400 (Exhaust Gas Recirculation Flow Malfunction), P0401 (Exhaust Gas Recirculation Flow Insufficient Detected), P0402 (Exhaust Gas Recirculation Flow Excessive Detected), P0420 (Catalyst System Efficiency Below Threshold (Bank 1)). These codes share the same subsystem (emissions) and often appear together. If you see this code, scan for the full code list — fixing the root cause usually clears multiple companion codes at once. If only P0411 is set without the companions, the issue is more isolated.
How do I prevent P0411 from coming back after a repair?
For P0411 (Secondary Air Injection System Incorrect Flow), prevention centers on the emissions system. Keep up with PM on the EGR system — clean the valve at 200K miles. Use OEM-spec air filters. Don't ignore minor codes; they often escalate into bigger emissions failures.