OBD-II Diagnostic Trouble Code
P0293 — Cylinder 11 Contribution/Balance
P0293 means the ECM detected that cylinder 11 is contributing an abnormal amount of power, based on crankshaft speed analysis. It only applies to engines with eleven or more cylinders, which are rare in trucks, so a code lookup or translation error should be ruled out first.
Severity 3/5
Truck-relevant
Service this week
Severity
Service this week
Cylinder 11 Contribution/Balance
Code
P0293
Category
Powertrain
Subsystem
Fuel
Truck-relevant
Yes
What this means for truckers
P0293 (Cylinder 11 Contribution/Balance) — same as P0287 but cylinder 11.
Before you replace parts — try this first
P0293 on the Fuel system is most often code misread or mistranslated on an engine without a cylinder 11 — not a dead part. On commercial diesels especially, work these in order before spending money on parts:
- Confirm the symptoms. Match what your truck is doing to the Symptoms section below. If the code is set but the symptoms are not there, clear the code and re-test after a drive cycle — it may not return.
- Clean and dry the sensor connector. Water, road salt, or oil seeping into a connector is the #1 fake sensor failure. Disconnect, look for green corrosion or moisture, spray with electrical contact cleaner, dry, reseat. Many faults clear here for $0.
- Inspect the wiring harness. Trace the wire from the sensor toward the ECM — look for chafing against the engine block, melted insulation near the turbo or exhaust, or pinch points where a clamp has rubbed through.
- Test the sensor before swapping it. Most Common Causes (below) list the expected voltage or resistance range — a $20 multimeter saves a $300 sensor swap that does not fix the problem.
- Only then, replace the part. Use the OEM or a tier-1 aftermarket. Cheap sensors throw the same code in two weeks.
Symptoms
On an engine with a cylinder 11, rough idle, vibration and a mild miss. Otherwise often no symptoms beyond the reported code.
Common causes
- CommonCode misread or mistranslated on an engine without a cylinder 11 ($100–$300)
- OccasionalWeak or leaking cylinder 11 injector ($200–$1000)
- OccasionalLow compression or valvetrain wear on cylinder 11 ($800–$5000)
How to fix
Confirm engine cylinder count and re-read codes with OEM or correctly configured software.
When to use: First.
Run a cylinder balance test and compression test.
When to use: When the engine has a cylinder 11.
Replace the injector or repair the mechanical fault.
When to use: Once the cause is confirmed.
Affects most
No specific vehicle pattern found in our complaint database. This code can appear on any vehicle that supports OBD-II diagnostics.
Related
- → Browse all DTC trouble codes
- → Decode a VIN to check codes for your truck
- → Owner-operator maintenance guides
- → P0200 — Injector Circuit Malfunction
- → P0201 — Injector Circuit Malfunction - Cylinder 1
- → P0202 — Injector Circuit Malfunction - Cylinder 2
- → P0203 — Injector Circuit Malfunction - Cylinder 3
- → P0204 — Injector Circuit Malfunction - Cylinder 4
Frequently Asked Questions
Can I drive with code P0293?
P0293 is severity 3 — plan service within a few days. Performance is likely degraded already (you may feel reduced power, harsher shifts, or slightly worse fuel economy). Continuing to drive risks additional damage to adjacent components.
How much does it cost to fix P0293 on a commercial truck?
Total repair cost ranges $100–$5000 depending on the root cause. The cheapest fix is usually the first one listed below — Code misread or mistranslated on an engine without a cylinder 11 — which is also the most common. On commercial trucks the cost is usually higher than passenger vehicles due to part availability and shop labor rates ($120–185/hour at most truck shops, vs $90–130 at general auto shops). DIY-capable fixes (sensors, hoses, filters) are at the low end; major component replacements (turbo actuator, high-pressure fuel pump, transmission solenoid pack) are at the high end. Always diagnose with a scan tool BEFORE replacing parts — guessing wrong on a $1,500 turbo actuator when the actual issue was a $30 boost hose is a common expensive mistake.
Will P0293 fail a DOT inspection?
P0293 itself doesn't automatically fail an inspection, but if the truck is in reduced-power mode (limp mode) at the time of inspection, it WILL be flagged. Most inspectors will note the check engine light but pass the truck if it's running and performance is normal. Fix it before a Level 1 inspection regardless.
What's the difference between P0293 and related codes?
P0293 is closely related to: P0200 (Injector Circuit Malfunction), P0201 (Injector Circuit Malfunction - Cylinder 1), P0202 (Injector Circuit Malfunction - Cylinder 2), P0203 (Injector Circuit Malfunction - Cylinder 3). These codes share the same subsystem (fuel) and often appear together. If you see this code, scan for the full code list — fixing the root cause usually clears multiple companion codes at once. If only P0293 is set without the companions, the issue is more isolated.
How do I prevent P0293 from coming back after a repair?
For P0293 (Cylinder 11 Contribution/Balance), prevention centers on the fuel system. Replace fuel filters at the OEM interval — don't stretch them. Use only diesel from high-volume fuel stops (avoid bottom-of-tank fuel at low-traffic stations). Add a water separator if you don't have one. After repair, prime the fuel system per the engine manual.