OBD-II Diagnostic Trouble Code
P0288 — Cylinder 10 Injector Circuit Low
P0288 means the ECM detected a low voltage or low current condition in the cylinder 10 injector control circuit, usually a short to ground or shorted injector coil. It applies only to engines with ten or more cylinders, such as V10 gas engines used in some medium-duty trucks.
Severity 4/5
Truck-relevant
Stop within 50 mi
Severity
Stop within 50 mi
Cylinder 10 Injector Circuit Low
Code
P0288
Category
Powertrain
Subsystem
Fuel
Truck-relevant
Yes
What this means for truckers
Stop within ~50 miles on a Cummins X15, Detroit DD15, PACCAR MX-13. Driving longer risks damaging adjacent components (turbo housing, head gasket, aftertreatment) and turning a $300 fix into a $3,000 fix.
Before you replace parts — try this first
P0288 on the Fuel system is most often cylinder 10 injector wiring shorted to ground — not a dead part. On commercial diesels especially, work these in order before spending money on parts:
- Confirm the symptoms. Match what your truck is doing to the Symptoms section below. If the code is set but the symptoms are not there, clear the code and re-test after a drive cycle — it may not return.
- Clean and dry the sensor connector. Water, road salt, or oil seeping into a connector is the #1 fake sensor failure. Disconnect, look for green corrosion or moisture, spray with electrical contact cleaner, dry, reseat. Many faults clear here for $0.
- Inspect the wiring harness. Trace the wire from the sensor toward the ECM — look for chafing against the engine block, melted insulation near the turbo or exhaust, or pinch points where a clamp has rubbed through.
- Test the sensor before swapping it. Most Common Causes (below) list the expected voltage or resistance range — a $20 multimeter saves a $300 sensor swap that does not fix the problem.
- Only then, replace the part. Use the OEM or a tier-1 aftermarket. Cheap sensors throw the same code in two weeks.
Symptoms
Cylinder 10 runs weak or dead, causing a steady miss, rough idle, vibration and low power, often with a cylinder 10 misfire code.
Common causes
- CommonCylinder 10 injector wiring shorted to ground ($150–$700)
- CommonShorted cylinder 10 injector coil ($200–$600)
- OccasionalContaminated or damaged injector connector ($100–$300)
- RareECM injector driver failure ($800–$2500)
How to fix
Confirm the engine has ten cylinders and the scan tool profile is correct.
When to use: When the code appears on an engine with fewer cylinders.
Measure cylinder 10 injector resistance and check for short to ground.
When to use: First electrical test.
Repair the harness or connector.
When to use: When the short is in the wiring.
Replace the cylinder 10 injector.
When to use: When the coil is shorted.
Affects most
No specific vehicle pattern found in our complaint database. This code can appear on any vehicle that supports OBD-II diagnostics.
Related
- → Browse all DTC trouble codes
- → Decode a VIN to check codes for your truck
- → Owner-operator maintenance guides
- → P0200 — Injector Circuit Malfunction
- → P0201 — Injector Circuit Malfunction - Cylinder 1
- → P0202 — Injector Circuit Malfunction - Cylinder 2
- → P0203 — Injector Circuit Malfunction - Cylinder 3
- → P0204 — Injector Circuit Malfunction - Cylinder 4
Frequently Asked Questions
Can I drive with code P0288?
Drive with caution. P0288 is severity 4 — stop within ~50 miles. Most commercial diesel codes at this severity (turbo, fuel rail, transmission solenoid) can damage adjacent expensive components if left unrepaired. Get to a service location before highway-speed loads.
How much does it cost to fix P0288 on a commercial truck?
Total repair cost ranges $100–$2500 depending on the root cause. The cheapest fix is usually the first one listed below — Cylinder 10 injector wiring shorted to ground — which is also the most common. On commercial trucks the cost is usually higher than passenger vehicles due to part availability and shop labor rates ($120–185/hour at most truck shops, vs $90–130 at general auto shops). DIY-capable fixes (sensors, hoses, filters) are at the low end; major component replacements (turbo actuator, high-pressure fuel pump, transmission solenoid pack) are at the high end. Always diagnose with a scan tool BEFORE replacing parts — guessing wrong on a $1,500 turbo actuator when the actual issue was a $30 boost hose is a common expensive mistake.
Will P0288 fail a DOT inspection?
P0288 itself doesn't automatically fail an inspection, but if the truck is in reduced-power mode (limp mode) at the time of inspection, it WILL be flagged. Most inspectors will note the check engine light but pass the truck if it's running and performance is normal. Fix it before a Level 1 inspection regardless.
What's the difference between P0288 and related codes?
P0288 is closely related to: P0200 (Injector Circuit Malfunction), P0201 (Injector Circuit Malfunction - Cylinder 1), P0202 (Injector Circuit Malfunction - Cylinder 2), P0203 (Injector Circuit Malfunction - Cylinder 3). These codes share the same subsystem (fuel) and often appear together. If you see this code, scan for the full code list — fixing the root cause usually clears multiple companion codes at once. If only P0288 is set without the companions, the issue is more isolated.
How do I prevent P0288 from coming back after a repair?
For P0288 (Cylinder 10 Injector Circuit Low), prevention centers on the fuel system. Replace fuel filters at the OEM interval — don't stretch them. Use only diesel from high-volume fuel stops (avoid bottom-of-tank fuel at low-traffic stations). Add a water separator if you don't have one. After repair, prime the fuel system per the engine manual.