OBD-II Diagnostic Trouble Code
P0164 — O2 Sensor Circuit High Voltage (Bank 2 Sensor 3)
P0164 means the bank 2 sensor 3 oxygen sensor voltage stayed above its expected maximum for a set time. This is a constant rich reading or a signal wire shorted to voltage. Sensor 3 is a post-catalyst sensor found only on certain exhaust layouts. This code applies mainly to gasoline trucks with multi-stage catalysts.
Severity 2/5
Less common on commercial trucks
Service soon
Severity
Service soon
O2 Sensor Circuit High Voltage (Bank 2 Sensor 3)
Code
P0164
Category
Powertrain
Subsystem
Emissions
Truck-relevant
Less common
What this means for truckers
Service this week. Not an immediate stop, but ignoring it usually leads to a more expensive fix downstream.
Before you replace parts — try this first
P0164 on the Emissions system is most often signal wire shorted to the heater feed or another voltage source — not a dead part. On commercial diesels especially, work these in order before spending money on parts:
- Confirm the symptoms. Match what your truck is doing to the Symptoms section below. If the code is set but the symptoms are not there, clear the code and re-test after a drive cycle — it may not return.
- Clean and dry the sensor connector. Water, road salt, or oil seeping into a connector is the #1 fake sensor failure. Disconnect, look for green corrosion or moisture, spray with electrical contact cleaner, dry, reseat. Many faults clear here for $0.
- Inspect the wiring harness. Trace the wire from the sensor toward the ECM — look for chafing against the engine block, melted insulation near the turbo or exhaust, or pinch points where a clamp has rubbed through.
- Test the sensor before swapping it. Most Common Causes (below) list the expected voltage or resistance range — a $20 multimeter saves a $300 sensor swap that does not fix the problem.
- Only then, replace the part. Use the OEM or a tier-1 aftermarket. Cheap sensors throw the same code in two weeks.
Symptoms
Check-engine light is on, and drivability is normal unless the engine really is running rich. In that case you may also see poor fuel economy, a sulfur smell or catalyst overheating. Expect an emissions readiness failure.
Common causes
- CommonSignal wire shorted to the heater feed or another voltage source ($100–$400)
- CommonFailed or contaminated sensor 3 ($110–$300)
- OccasionalReal rich condition on bank 2 ($150–$900)
- RareECM input fault ($900–$2200)
How to fix
Compare all bank 2 sensors and fuel trims to see whether the rich reading is real.
When to use: First step
Unplug the sensor and test the signal circuit for voltage with the key on.
When to use: When fuel trims are normal
Replace sensor 3.
When to use: When the wiring tests good
Affects most
No specific vehicle pattern found in our complaint database. This code can appear on any vehicle that supports OBD-II diagnostics.
Related
- → Browse all DTC trouble codes
- → Decode a VIN to check codes for your truck
- → Owner-operator maintenance guides
- → P0100 — Mass or Volume Air Flow Circuit
- → P0101 — Mass or Volume Air Flow Circuit Range/Performance
- → P0102 — Mass or Volume Air Flow Circuit Low Input
- → P0103 — Mass or Volume Air Flow Circuit High Input
- → P0104 — Mass or Volume Air Flow Circuit Intermittent
Frequently Asked Questions
Can I drive with code P0164?
P0164 is severity 2 — service this week. Not an immediate stop, but ignoring it usually compounds the problem. Most common cause for this code is a worn sensor or minor performance fault that won't strand you today but will get more expensive the longer you wait.
How much does it cost to fix P0164 on a commercial truck?
Total repair cost ranges $100–$2200 depending on the root cause. The cheapest fix is usually the first one listed below — Signal wire shorted to the heater feed or another voltage source — which is also the most common. On commercial trucks the cost is usually higher than passenger vehicles due to part availability and shop labor rates ($120–185/hour at most truck shops, vs $90–130 at general auto shops). DIY-capable fixes (sensors, hoses, filters) are at the low end; major component replacements (turbo actuator, high-pressure fuel pump, transmission solenoid pack) are at the high end. Always diagnose with a scan tool BEFORE replacing parts — guessing wrong on a $1,500 turbo actuator when the actual issue was a $30 boost hose is a common expensive mistake.
Will P0164 fail a DOT inspection?
Yes — P0164 is an emissions-related code, and DOT inspectors check emissions compliance. An active emissions code with a check engine light can result in an out-of-service violation under FMCSA Part 393. The truck typically can't be moved until the code is cleared. Repeated emissions violations escalate to CSA scores.
What's the difference between P0164 and related codes?
P0164 is closely related to: P0100 (Mass or Volume Air Flow Circuit), P0101 (Mass or Volume Air Flow Circuit Range/Performance), P0102 (Mass or Volume Air Flow Circuit Low Input), P0103 (Mass or Volume Air Flow Circuit High Input). These codes share the same subsystem (emissions) and often appear together. If you see this code, scan for the full code list — fixing the root cause usually clears multiple companion codes at once. If only P0164 is set without the companions, the issue is more isolated.
How do I prevent P0164 from coming back after a repair?
For P0164 (O2 Sensor Circuit High Voltage (Bank 2 Sensor 3)), prevention centers on the emissions system. Keep up with PM on the EGR system — clean the valve at 200K miles. Use OEM-spec air filters. Don't ignore minor codes; they often escalate into bigger emissions failures.