OBD-II Diagnostic Trouble Code
P0113 — Intake Air Temperature Sensor 1 Circuit High
P0113 means the IAT 1 signal voltage is too high, which the ECM reads as extremely cold intake air. This is usually caused by an open circuit, such as an unplugged sensor, a broken wire, or a failed sensor.
Severity 2/5
Truck-relevant
Service soon
Severity
Service soon
Intake Air Temperature Sensor 1 Circuit High
Code
P0113
Category
Powertrain
Subsystem
Air Flow
Truck-relevant
Yes
What this means for truckers
Service this week on a Cummins X15, Detroit DD15, PACCAR MX-13. Not an immediate stop, but ignoring it usually leads to a more expensive fix downstream.
Before you replace parts — try this first
P0113 on the Air Flow system is most often unplugged iat sensor or loose connector — not a dead part. On commercial diesels especially, work these in order before spending money on parts:
- Confirm the symptoms. Match what your truck is doing to the Symptoms section below. If the code is set but the symptoms are not there, clear the code and re-test after a drive cycle — it may not return.
- Clean and dry the sensor connector. Water, road salt, or oil seeping into a connector is the #1 fake sensor failure. Disconnect, look for green corrosion or moisture, spray with electrical contact cleaner, dry, reseat. Many faults clear here for $0.
- Inspect the wiring harness. Trace the wire from the sensor toward the ECM — look for chafing against the engine block, melted insulation near the turbo or exhaust, or pinch points where a clamp has rubbed through.
- Test the sensor before swapping it. Most Common Causes (below) list the expected voltage or resistance range — a $20 multimeter saves a $300 sensor swap that does not fix the problem.
- Only then, replace the part. Use the OEM or a tier-1 aftermarket. Cheap sensors throw the same code in two weeks.
Symptoms
Check engine light. The ECM may run cold-start strategies, so you may see rough running, extra smoke, longer grid heater or intake heater cycles, or poor fuel economy. Many trucks show no other symptoms.
Common causes
- CommonUnplugged IAT sensor or loose connector ($20–$150)
- CommonOpen signal or ground wire ($80–$350)
- CommonOpen (failed) IAT sensor ($60–$450)
- OccasionalCorroded connector pins ($30–$200)
How to fix
Check that the sensor is plugged in and the connector is locked
When to use: First step, especially after air filter or intake work
Jumper the signal and ground pins at the harness side; a very hot reading means the wiring is good
When to use: To separate an open sensor from an open wire
Check continuity of the signal and ground wires to the ECM
When to use: When the jumper test does not change the reading
Replace the IAT sensor
When to use: When the sensor reads open on a resistance check
Affects most
No specific vehicle pattern found in our complaint database. This code can appear on any vehicle that supports OBD-II diagnostics.
Related
- → Browse all DTC trouble codes
- → Decode a VIN to check codes for your truck
- → Owner-operator maintenance guides
- → P0100 — Mass or Volume Air Flow Circuit
- → P0101 — Mass or Volume Air Flow Circuit Range/Performance
- → P0102 — Mass or Volume Air Flow Circuit Low Input
- → P0103 — Mass or Volume Air Flow Circuit High Input
- → P0104 — Mass or Volume Air Flow Circuit Intermittent
Frequently Asked Questions
Can I drive with code P0113?
P0113 is severity 2 — service this week. Not an immediate stop, but ignoring it usually compounds the problem. Most common cause for this code is a worn sensor or minor performance fault that won't strand you today but will get more expensive the longer you wait.
How much does it cost to fix P0113 on a commercial truck?
Total repair cost ranges $20–$450 depending on the root cause. The cheapest fix is usually the first one listed below — Unplugged IAT sensor or loose connector — which is also the most common. On commercial trucks the cost is usually higher than passenger vehicles due to part availability and shop labor rates ($120–185/hour at most truck shops, vs $90–130 at general auto shops). DIY-capable fixes (sensors, hoses, filters) are at the low end; major component replacements (turbo actuator, high-pressure fuel pump, transmission solenoid pack) are at the high end. Always diagnose with a scan tool BEFORE replacing parts — guessing wrong on a $1,500 turbo actuator when the actual issue was a $30 boost hose is a common expensive mistake.
Will P0113 fail a DOT inspection?
P0113 is generally not a direct DOT inspection fail item by itself. Inspectors focus on safety-critical systems (brakes, steering, tires, lights, hours-of-service). However, the check engine light alone can trigger additional inspection scrutiny. Best practice: fix the code and clear it before a planned inspection.
What's the difference between P0113 and related codes?
P0113 is closely related to: P0100 (Mass or Volume Air Flow Circuit), P0101 (Mass or Volume Air Flow Circuit Range/Performance), P0102 (Mass or Volume Air Flow Circuit Low Input), P0103 (Mass or Volume Air Flow Circuit High Input). These codes share the same subsystem (air-flow) and often appear together. If you see this code, scan for the full code list — fixing the root cause usually clears multiple companion codes at once. If only P0113 is set without the companions, the issue is more isolated.
How do I prevent P0113 from coming back after a repair?
For P0113 (Intake Air Temperature Sensor 1 Circuit High), prevention centers on the air flow system. Service air filter on time. Clean MAF sensor at every air filter change. Inspect intake boots/hoses for cracks — vibration kills them eventually.