OBD-II Diagnostic Trouble Code
C0134 — ABS Pressure Sensor Circuit High
C0134 means the ABS pressure sensor circuit is reading high. The ABS module saw the signal voltage above its valid range, which usually means an open sensor ground or the signal shorted to the reference or battery voltage. The sensor itself can also fail high.
Severity 4/5
Truck-relevant
Stop within 50 mi
Severity
Stop within 50 mi
ABS Pressure Sensor Circuit High
Code
C0134
Category
Chassis
Subsystem
Brakes
Truck-relevant
Yes
What this means for truckers
C0134 (ABS Pressure Sensor High) — open or shorted to power.
Before you replace parts — try this first
C0134 on the Brakes system is most often open sensor ground or signal shorted to voltage — not a dead part. On commercial diesels especially, work these in order before spending money on parts:
- Confirm the symptoms. Match what your truck is doing to the Symptoms section below. If the code is set but the symptoms are not there, clear the code and re-test after a drive cycle — it may not return.
- Clean and dry the sensor connector. Water, road salt, or oil seeping into a connector is the #1 fake sensor failure. Disconnect, look for green corrosion or moisture, spray with electrical contact cleaner, dry, reseat. Many faults clear here for $0.
- Inspect the wiring harness. Trace the wire from the sensor toward the ECM — look for chafing against the engine block, melted insulation near the turbo or exhaust, or pinch points where a clamp has rubbed through.
- Test the sensor before swapping it. Most Common Causes (below) list the expected voltage or resistance range — a $20 multimeter saves a $300 sensor swap that does not fix the problem.
- Only then, replace the part. Use the OEM or a tier-1 aftermarket. Cheap sensors throw the same code in two weeks.
Symptoms
The ABS or stability lamp is on and stability or traction control may be disabled.
Common causes
- CommonOpen sensor ground or signal shorted to voltage ($80–$300)
- CommonFaulty pressure sensor ($150–$500)
- RareFaulty ABS module ($600–$2000)
How to fix
Check the sensor ground circuit
When to use: First step
Check the signal wire for a short to voltage and repair it
When to use: When the ground is good
Replace the sensor
When to use: When the wiring tests good
Affects most
No specific vehicle pattern found in our complaint database. This code can appear on any vehicle that supports OBD-II diagnostics.
Related
- → Browse all DTC trouble codes
- → Decode a VIN to check codes for your truck
- → Owner-operator maintenance guides
- → C0110 — Pump Motor Circuit Malfunction
- → C0121 — Valve Relay Circuit Malfunction
- → C0131 — ABS Pressure Sensor Circuit
- → C0161 — ABS / TCS Brake Switch Circuit
- → C0186 — Yaw Rate Sensor Bias Circuit
Frequently Asked Questions
Can I drive with code C0134?
Drive with caution. C0134 is severity 4 — stop within ~50 miles. Most commercial diesel codes at this severity (turbo, fuel rail, transmission solenoid) can damage adjacent expensive components if left unrepaired. Get to a service location before highway-speed loads.
How much does it cost to fix C0134 on a commercial truck?
Total repair cost ranges $80–$2000 depending on the root cause. The cheapest fix is usually the first one listed below — Open sensor ground or signal shorted to voltage — which is also the most common. On commercial trucks the cost is usually higher than passenger vehicles due to part availability and shop labor rates ($120–185/hour at most truck shops, vs $90–130 at general auto shops). DIY-capable fixes (sensors, hoses, filters) are at the low end; major component replacements (turbo actuator, high-pressure fuel pump, transmission solenoid pack) are at the high end. Always diagnose with a scan tool BEFORE replacing parts — guessing wrong on a $1,500 turbo actuator when the actual issue was a $30 boost hose is a common expensive mistake.
Will C0134 fail a DOT inspection?
C0134 is generally not a direct DOT inspection fail item by itself. Inspectors focus on safety-critical systems (brakes, steering, tires, lights, hours-of-service). However, the check engine light alone can trigger additional inspection scrutiny. Best practice: fix the code and clear it before a planned inspection.
What's the difference between C0134 and related codes?
C0134 is closely related to: C0110 (Pump Motor Circuit Malfunction), C0121 (Valve Relay Circuit Malfunction), C0131 (ABS Pressure Sensor Circuit), C0161 (ABS / TCS Brake Switch Circuit). These codes share the same subsystem (brakes) and often appear together. If you see this code, scan for the full code list — fixing the root cause usually clears multiple companion codes at once. If only C0134 is set without the companions, the issue is more isolated.
How do I prevent C0134 from coming back after a repair?
For C0134 (ABS Pressure Sensor Circuit High), prevention centers on the brakes system. Clean wheel speed sensors at every brake service. Inspect tone rings for cracks or rust. Keep ABS sensor harnesses away from chafe points. Don't drive through deep water that can flood the rear wheel-speed sensor connectors.