Skip to main content
O Trucking
Commercial Truck Axle

Meritor RT-46-160 (tandem drive, 46K, vocational)

Meritor · Tandem Drive axle · 46,000 lb GAWR

Class 8 In production
Tandem Drive
Manufacturer
Meritor
Type
Tandem Drive
GAWR
46,000 lb
Class
Class 8

What this axle does

The Meritor RT-46-160 is a 46,000 lb vocational tandem drive — Meritor's equivalent to Dana D-52-190 (though lighter rated). Used in dump, concrete mixer, refuse, and mid-range vocational applications. Vocational gear ratios (3.42-4.88) for mixed terrain and severe-duty starts.

Specifications
Manufacturer
Meritor
Type
Tandem Drive
GAWR
46,000 lb
Ratio options
3.42, 3.73, 4.10, 4.30, 4.56, 4.88
Truck class
Class 8
Production
2005–present
Applications
Vocational, dump, concrete mixer, regional vocational
Design and engineering

Tandem drive optimized for vocational duty cycles. Reinforced inter-axle differential. Wide ratio range.

Generations and major changes
  • RT-46-160 (2005–present)
    Long production run.
Reliability and longevity

Strong vocational reliability.

Common problems

Vocational duty cycle wear on inter-axle differential.

Maintenance schedule

Differential lube every 100K-150K miles in severe-duty.

Pros and cons

Pros

  • ✓Meritor vocational standard
  • ✓Wide ratio range
  • ✓OEM-fitted across major brands

Cons

  • !46K rating — lighter than Dana D-52-190 for heavy-haul
Resale value impact

Standard for vocational.

Trucks that use this axle
Other Meritor axles

Related

Frequently Asked Questions

What is the Meritor RT-46-160 (tandem drive, 46K, vocational) GAWR?
The Meritor RT-46-160 (tandem drive, 46K, vocational) is rated for 46,000 lb Gross Axle Weight Rating (GAWR). GAWR is the maximum weight the axle can support, including the chassis, suspension, body, and payload distributed to that axle. For a tandem-drive configuration, the rating is the combined capacity of both rear axles. Steer axles typically range 12,000-22,000 lb depending on application; tandem drives range 38,000-58,000 lb.
What gear ratios are available for the Meritor RT-46-160 (tandem drive, 46K, vocational)?
The Meritor RT-46-160 (tandem drive, 46K, vocational) offers these ratio options: 3.42, 3.73, 4.10, 4.30, 4.56, 4.88. Lower numerical ratios (e.g., 2.47, 2.64) are taller — better for highway fuel economy at the cost of acceleration. Higher numerical ratios (e.g., 4.10, 4.56) are shorter — better for vocational/severe-duty starts and grade-climbing at the cost of highway fuel economy. Fleet spec engineers select the ratio based on average loaded weight, terrain, and target cruise speed.
What's the difference between a single drive and tandem drive axle?
A single-drive axle has one driven rear axle — typical of Class 6-7 medium-duty trucks. A tandem-drive axle has two driven rear axles connected via an inter-axle differential — typical of Class 8 trucks. Tandems provide more traction, allow heavier loads (40,000-58,000 lb combined GAWR vs 23,000-32,000 lb single-drive), and better handle severe-duty/loose-surface conditions because both rear axles can drive. The trade-off: more weight, more cost, more components to service.
How long should the Meritor RT-46-160 (tandem drive, 46K, vocational) last?
For highway-duty Class 8 axles, expect 1,000,000+ miles before major hypoid gear or pinion overhaul, with proper synthetic-lube service intervals (every 250,000 miles). Vocational/severe-duty axles see 600,000-800,000 miles before similar service due to higher load cycling and frequent inter-axle differential lockout engagement. Steer axles last similarly long for the bearings and gears, but king-pins typically need replacement at 750,000-1,000,000 miles in highway use (500K-700K in severe-duty).
How do I know if my axle needs service?
Warning signs: differential lube leak at the pinion seal (visible under the rear of the truck), hypoid gear noise (whine that varies with throttle), wheel bearing growl (changes pitch with speed), king-pin slop (steering wander or clunking on turns). For preventive: pull a lube sample at every PM service and have it analyzed — metal content trending up signals internal wear before it becomes a failure. Most fleets pull samples at 100K and analyze every 250K.
Can I swap a Dana axle for a Meritor (or vice versa)?
Generally yes for the same GAWR class — both manufacturers build to similar SAE specifications for major dimensions, suspension mounting points, and brake mounting. However: ratio options differ, wheel bearings differ slightly, axle shafts are NOT interchangeable, and brake controllers may need to be reconfigured for different ABS sensor patterns. For a fleet swap, plan the cross-reference carefully — many fleets choose to standardize on one supplier (all-Dana or all-Meritor) to simplify parts stocking and tech training.

Need help speccing axles for a new build?

Ready to Grow Your Trucking Business?

Dispatch support for your trucking business. Explore our current service options.